IC-706 MARK II - KEY CHART AND MENU LIST

Note:  When describing Front Panel controls, progression is top to bottom and
left to right.  Side panel controls are front to back.

Down left side:
Power on/off.
Preamp/Attenuator, short press toggles preamp while pressing for two seconds
activates the attenuator (short press again turns off attenuator.
Tune/Call:  through 6 meters short press toggles tuner on/off; press and hold
to activate outboard auto tuner; above 6 meters switches to call channel.

Next row right:
AF gain, inner knob, RF gain outer ring.
RIT/Sub switch:  function set in initial set mode.
M/CH inner knob (also used for RIT); IF shift, outer ring.

Across bottom:
Menu (long beep at 1), F1, F2, F3.

Left of main dial:
Mode:  short press cycles through ssb, cw, rtty and am; press and hold in
various modes to select opposite sideband, cw r, rtty r, fm or wide fm.
Tuning step:  short press switches tuning speed; press and hold for 2 seconds
to set tuning step for each mode; short press to exit.
Display:  short presses cycle through m, s and g menus (long beep at m;
press and hold for 2 seconds to activate quick set mode, short press to exit.
Lock:  short press toggles dial lock; press for 2 seconds for voice.

Right of main dial:
Band up, band down.

Right Side Panel
Comp gain; sidetone/beep level; vox gain; antivox.

Menu Lists
Quick Set (mode dependent)

Q1: RF power, all modes.
Q2: mic gain (ssb,am,fm); pitch (cw); tone (rtty).
Q3: vox delay (ssb,am,fm); break-in delay (cw); shift (rtty).
Q4: carrier frequency (ssb); repeater tone (fm); paddle type (cw);
    keying polarity (rtty).
Q5: tone squelch (fm); key speed (cw).
Q6: ratio (cw).

Menus 
General
M1:  f1, split (press 2 seconds for quick split mode); f2, a/b; f3, a=b
     (xfc in split mode.
M2:  f1, mw; f2, mcl/move (hold for two seconds for mcl in memory mode and
     memory to vfo transfer in vfo mode); f3 m/vfo.
M3:  f1, filter toggle; f2, noise blanker; f3, meter toggle.
M4:  SSB:  f1, vox; f2, comp; f3, agc.
     CW:  f1, 1/4; f2, brk; f3, agc.
          RTTY:  f1, 1/4; f2, ---; f3, agc.
               FM:  f1, vox; f2, com; f3, ton.
          S1:  f1, mw; f2, mpw; f3, mpr.
S2:  f1, scn; f2, pri sel; f3, v/m.
S3:  (band stacking register) f1, 7; f2, 50; f3, 144.
S4:  f1, anf; f2, nr; f3, nr level (adjust by m/ch knob).
G1:  band scope.
G2:  if shift.
G3:  tx freq.
G4:  memory name.

Initial Set Mode
1:  beep
2:  band beep
3:  auto off
4:  peak hold
5:  backlight
6:  speech lang.
7:  speech spd.
8:  s-lvl spch.
9:  scan resume
10:  scan speed
11:  u/d speed
12:  A-tune start
13:  ptt tune
14:  pad ch.
15:  quick split
16:  spl offset
17:  dup offset
18:  split lock
19:  opt. fil1
20:  opt. fil2
21:  rf gain
22:  am nb
23:  pow. on chk.
24:  subdial rit
25:  ci-v addres
26:  ci-v baud
27:  ci-v trn
28:  ci-v 731